NXP Semiconductors
PCA9685
16-channel, 12-bit PWM Fm+ I 2 C-bus LED controller
7.3.6 SUBADR1 to SUBADR3, I 2 C-bus subaddress 1 to 3
Table 8.
SUBADR1 to SUBADR3 - I 2 C-bus subaddress registers 0 to 3 (address 02h to
04h) bit description
Legend: * default value.
Address
Register
Bit
Symbol
Access Value
Description
02h
SUBADR1
7:1
A1[7:1]
R/W
1110 001*
I 2 C-bus subaddress 1
0
A1[0]
R only
0* reserved
03h
SUBADR2
7:1
A2[7:1]
R/W
1110 010*
I 2 C-bus subaddress 2
0
A2[0]
R only
0* reserved
04h
SUBADR3
7:1
A3[7:1]
R/W
1110 100*
I 2 C-bus subaddress 3
0
A3[0]
R only
0* reserved
Subaddresses are programmable through the I 2 C-bus. Default power-up values are E2h,
E4h, E8h, and the device(s) will not acknowledge these addresses right after power-up
(the corresponding SUBx bit in MODE1 register is equal to 0).
Once subaddresses have been programmed to their right values, SUBx bits need to be
set to logic 1 in order to have the device acknowledging these addresses (MODE1
register).
Only the 7 MSBs representing the I 2 C-bus subaddress are valid. The LSB in SUBADRx
register is a read-only bit (0).
When SUBx is set to logic 1, the corresponding I 2 C-bus subaddress can be used during
either an I 2 C-bus read or write sequence.
7.3.7 ALLCALLADR, LED All Call I 2 C-bus address
Table 9.
ALLCALLADR - LED All Call I 2 C-bus address register (address 05h) bit
description
Legend: * default value.
Address
Register
Bit
Symbol
Access Value
Description
05h
ALLCALLADR
7:1
AC[7:1]
R/W
1110 000*
ALLCALL I 2 C-bus
address register
0
AC[0]
R only
0* reserved
The LED All Call I 2 C-bus address allows all the PCA9685s in the bus to be programmed
at the same time (ALLCALL bit in register MODE1 must be equal to 1 (power-up default
state)). This address is programmable through the I 2 C-bus and can be used during either
an I 2 C-bus read or write sequence. The register address can also be programmed as a
Sub Call.
Only the 7 MSBs representing the All Call I 2 C-bus address are valid. The LSB in
ALLCALLADR register is a read-only bit (0).
If ALLCALL bit = 0, the device does not acknowledge the address programmed in register
ALLCALLADR.
PCA9685
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 2 September 2010
? NXP B.V. 2010. All rights reserved.
25 of 51
相关PDF资料
PCA9922PW,118 IC LED DRIVER LINEAR 16-TSSOP
PCA9955TW,118 IC LED DRVR CONST CURR
PCF85102C-2P/03,11 IC EEPROM 2KBIT 100KHZ 8DIP
PCF85103C-2T/00,11 IC EEPROM 2KBIT 100KHZ 8SOIC
PCF8570T/F5,512 IC SRAM 2KBIT 100KHZ 8SOIC
PCF8582C-2T/03,118 IC EEPROM 2KBIT 100KHZ 8SOIC
PCF8594C-2T/02,118 IC EEPROM 4KBIT 100KHZ 8SOIC
PCF8598C-2P/02,112 IC EEPROM 8KBIT 100KHZ 8DIP
相关代理商/技术参数
PCA9685PW/Q900,118 功能描述:LED显示驱动器 LED Driver 2.3V-5.5V 6mA RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
PCA9691BS/1 制造商:NXP Semiconductors 功能描述:IC ADC/DAC 8-BIT I2C 16-HVQFN 制造商:NXP Semiconductors 功能描述:IC, ADC/DAC, 8-BIT, I2C, 16-HVQFN
PCA9691BS/1,118 功能描述:I2C 接口集成电路 ADC/DAC 16-Pin HVQFN EP RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16
PCA9691BS/1118 制造商:NXP Semiconductors 功能描述:PCA9691BS/HVQFN16/REEL13//1
PCA9691T/1,112 制造商:NXP Semiconductors 功能描述:
PCA9691T/1,118 制造商:NXP Semiconductors 功能描述:
PCA9691T/1,512 功能描述:I2C 接口集成电路 8b A/D AND D/A COVERTER RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16
PCA9691T/1,518 功能描述:模数转换器 - ADC 8-bit A/D and D/A converter RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32